Account
My Items
OR
Poly line, 210 lb. average breaking strength, can be blown into conduit and then used to pull in a larger pulling rope or it can be used directly to pull in smaller wires. Can be used directly from...
Poly line, 210 lb. average breaking strength, can be blown into conduit and then used to pull in a larger pulling rope or it can be used directly to pull in smaller wires. Can be used directly from the container with power fishing systems. Resists tangling when dispensing. Prepunched hole for dispensing the line. Rot and mildew-resistant.Unit: EA
Shorter for better access to tight spaces between studs and joists, will drill 2 ft and 4 ft joists. Self-feeding screw point draws bit through all wood types. Replaces special tools such as right...
Shorter for better access to tight spaces between studs and joists, will drill 2 ft and 4 ft joists. Self-feeding screw point draws bit through all wood types. Replaces special tools such as right angle drills and eliminates multiple steps to cut the hole to size. Overall length 4.5 in (144 mm) weight 0.3 lb. (118 g). 1/4 in hex. Over center single flute design for cleaner holes and less splintering. Marked with bit diameter and catalog number on shank for easy identification. Not for use in...
Cutting edge is hardened for longer life. Self-feeding screw point draws bit through wood even after multiple sharpening's. Made of high quality carbon alloy steel, cuts through nails and provides...
Cutting edge is hardened for longer life. Self-feeding screw point draws bit through wood even after multiple sharpening's. Made of high quality carbon alloy steel, cuts through nails and provides up to 3X longer life. Overall length 18 in. Hex shank: 7/16 in (11.1mm). Weight: 1.5 lb, (681g).Unit: EA
Contains 100 anchors, 100 screws and a 1/4 in masonry drill bit. For use in concrete, block, tile and brick. Moisture and chemical resistant, for indoor or outdoor use.Unit: EA
Kit includes 921-18, 18 in quick connect extension, 921-36, 36 in quick connect extension, 150Q, 1/2 in cable pulling grip and 60A-3/4, 3/4 in auger bit.Unit: EA
Clamp-on meter for taking basic AC amperage measurements 20, 200, 400 A and has data hold and max hold 2000 count LCD display and a jaw that opens to 1.06 in. Category III 600 V safety rating per UL...
Clamp-on meter for taking basic AC amperage measurements 20, 200, 400 A and has data hold and max hold 2000 count LCD display and a jaw that opens to 1.06 in. Category III 600 V safety rating per UL 61010B-1. Carrying case included.Unit: EA
Measures AC amperage, AC/DC voltage and resistance. True RMS for accurate measurements when the voltage or current waveform is distorted by non-linear loads. Amperage measurement 400, 600 A. Voltage...
Measures AC amperage, AC/DC voltage and resistance. True RMS for accurate measurements when the voltage or current waveform is distorted by non-linear loads. Amperage measurement 400, 600 A. Voltage measurement 400, 600 V. 3-1/2-digit LCD display. Jaw opens 1.38 in. Auto-power off for longer battery life. Measurement category Cat III, 600 V per UL 3111-1.Unit: EA
Use to measure voltage and check batteries, measure current of small electronic circuits. 600 VAC/VDC voltage. Resistance measurement. 1.5 V/9 V battery test. Continuity and diode tests. Built-in...
Use to measure voltage and check batteries, measure current of small electronic circuits. 600 VAC/VDC voltage. Resistance measurement. 1.5 V/9 V battery test. Continuity and diode tests. Built-in test leads and a rubber boot to protect meter from damage. 9 V battery included. Measurement category Cat III, 600 V. ETL approved.Unit: EA
For most electrical needs. 600 VAC/VDC voltage test, 10 AC/DC amperage measurement. Temperature testing with thermocouple rated -58 to 400 deg F (-50 to 204 deg C). Continuity, diode, duty cycle and...
For most electrical needs. 600 VAC/VDC voltage test, 10 AC/DC amperage measurement. Temperature testing with thermocouple rated -58 to 400 deg F (-50 to 204 deg C). Continuity, diode, duty cycle and frequency testing. Resistance and capacitance measurement. Includes hold, relative reading, backlight, automatic power off and field replaceable fuses. 9 V battery included. Measurement category Cat III, 600 V. ETL approved.Unit: EA
Drill/tap high-speed steel bit, split point with web thinning. High-quality hex shank to ensure strong connection to drill chuck. Complete hole drilling, tapping and deburring or countersinking in...
Drill/tap high-speed steel bit, split point with web thinning. High-quality hex shank to ensure strong connection to drill chuck. Complete hole drilling, tapping and deburring or countersinking in one operation with power drill. Designed to tap up to 10 ga metal. Back taper or deburr or countersink beyond tap to prevent thread damage from over-drilling.Unit: EA